Munji 4x4 Accessories Pty Ltd

Contact Us
Jared's Mobile: 0404 797 034
Order Enquires: 0756 708 147

Jared's Mobile: 0404 797 034 | Order Enquires: 0756 708 147

X

Vent to Atmosphere Chassis Kit (RA, RA7, RC, and early D-Max) - PRE-ORDER!!!

SKU: I-S1-VTACF

$155.00

FREE STANDARD SHIPPING AUSTRALIA WIDE

or make 4 interest‐free payments of $38.75 fortnightly with Afterpay Moreinfo

Let me know when it's back in stock!

Give us a few of your details and we'll let you know when this product is back in stock.

N.B. IF YOU HAVE A STANDARD EXHAUST - SEE NOTE IN RED BELOW

What is this?

This is a kit that is the only 100% removal of blowby crankcase pressure and oil from your intake and no servicing needed!!

There is NO risk of pressure build up from a restrictive filter and no draining needed. 

With the gasses being evenly pumped into both chassis rails you will not only get no dripping but you will also get an even coating (very thin) of oil througout the entire chassis rails. This is one of the best rust preventions you can have on any car that is exposed to the atmospher not to forget for those who drive on salted roads.

Normally vent to atmosphere is a pipe to the ground... there are many bad things there eg:

  • Oil vapour on the road is not kind to motorbike riders or other vehicles
  • Oil vapour on the road is not kind on the road surface in general
  • Can be easily seen venting into the air

This kit comes with all that is needed and is vehicle specific. 

These kits will include:

  • Specific chassis fittings made to fit original holes with no cutting needed.
  • Angle barb fittings that fit to the chassis plates
  • Y piece to distribute to both rails
  • T piece to tap into the original breather (one blocked end to make it look "neater"
  • Silicone pipe to connect all the fittings neatly.
  • All fittings are billet alloy anodised black also the silicone pipe supplied is black for a "neater" look..

N.B. Vent to atmosphere modifications are not legal.

What are the benefits?

100% removal of venting gasses and oil from intake system.

What is this product made from?

Billet alloy.

Standard Exhaust?

The early Isuzu's that still run stock exhaust and no mods may find the drivers side fitting interfering with the flex pipe in the exhaust. In this case there is a similar hole 300mm further back that can be used but will need to drill a 5mm hole and tap the thread or 7mm hole to suit the m8 bolt on the other side. In this case please add a note on the order to include 2x m8 bolts and washers.

If your vehicle has a standard i.e. stock, exhaust, installation instructions change slightly for the drivers side.

In addition, you will need to tap a thread into the large hole just beyond the flexi join, but before the catylic converter. We have an optional rental service for the required 1/2" BSP Tap.

The rental fee is $35.00, and $30.00 is refunded to you within three (3) business days once you return the tap to us (at your expense).

Missing mounting holes in chassis?

We noticed some of the earlier model RA's don't have the smaller screw holes on the chassis rails. However, you can line the plate up in the rectangle hole, mark the location of the small mounting hole and drill out to 5mm on one side and 7mm on the other side. Tap the 5mm hole with an M6x1 tap and the 7mm hole with an M8x1.25 tap.

What vehicles does this suit?

- Holden RA Rodeo (2003-2006)

- Holden RA7 Rodeo (2007-2008)

- Holden RC Colorado (2008-2012)

- Isuzu D-Max (2008-2012)

Installation

Tools required –  screwdriver / degreaser / rags / allan key set / knife

Installation Time - Approximately 30 minutes

Difficulty – Do it yourself, basic tool knowledge required / Detailed installation guide provided, basic tool knowledge required 

Postage

Standard postage Australia wide included in price / Express post Australia wide included / Postage additional, calculated at checkout